100% Owned PL 59 Intercepts 18M of Disseminated Sulphides
Released
Released
Announcement PDF
ABN 96 122 995 073
TO:
DATE:
COMPANY ANNOUNCEMENTS OFFICE
ASX LIMITED
26 OCTOBER 2015
ASX Code: BML
THIS IS A PRIORITY ITEM
SULPHIDES INTERSECTED IN FIRST HOLE OF DRILL PROGRAM
AT BML’S 100% OWNED PL 59/2008 IN BOTSWANA
PL 59/2008 (PL 59) MAIBELE NORTH EXTENSION:
DRILLING AT THE “MAIBELE NORTH EXTENSION” PROSPECT, PREVIOUSLY
IDENTIFIED BY SQUID EM AND VTEM SURVEYs, HAS INTERSECTED AN 18M
THICK ZONE OF DISSEMINATED SULPIDES (PYRRHOTITE) AT A DOWNHOLE
DEPTH OF ~210M.
THE INTERSECTION PROVIDES PROOF OF THE GEOLOGICAL MODEL AND
TARGETING STRATEGY EMPLOYED BY BML AND PROVIDES GREAT
ENCOURAGEMENT FOR THE FUTURE DISCOVERY OF POTENTIAL NISULPHIDE ACCUMULATIONS IN THE REGION.
THE MAIBELE NORTH EXTENSION PROSPECT IS ONLY 4KM TO THE EAST OF THE
MAIBELE NORTH JORC RESOURCE HELD BY BML AND JV PARTNER BCL LIMITED.
The first drill hole of the proposed 3 hole, 775m RC program designed to test a number of
prominent EM Conductors identified by recent SQUID EM surveys is now complete. The hole,
MNRC001, was drilled to a depth of 250m into conductor E4 and intersected a thick zone of
weakly disseminated pyrrhotite (host sulphide for Nickel at Maibele North) within a medium
grained amphibolite body from between 200 to 218m down hole. The intersection lies close to
the predicted downhole position of the modelled SQUID conductor plate. The RC samples
have been submitted for assay to confirm nickel & copper content.
This intersection is highly significant because:
It is the first and only drill hole into the new prospect which lies between 4km to 7km
east of Maibele North along an interpreted Ni-mineralised horizon.
It is the first drill hole into a large (>3km long) VTEM and SQUID EM anomaly which
now has been proven to be associated with sulphide mineralisation.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
It is the first hole into the very strong, 500m long E4 conductor leaving great scope for
further sulphide intersections along the plate.
It demonstrates that sulphide mineralising processes similar to that occurring at
Maibele North are present at Maibele North Extension, over 6.5km away from hole
MNRC001.
It verifies the interpretation of a preferential regional geological horizon for sulphide
mineralisation that encompasses Maibele North, Airstrip Cu, anomaly 10380a and the
three 100%-owned BML projects Maibele North Extension, Mashambe and Mashambe
NE.
It continues the 100% sulphide intersection success rate of testing SQUID EM
conductors in the region.
It confirms the mineralised potential of the area and highlights the vast area of
unexplored prospective terrain within BML’s portfolio.
The Board of Botswana Metals is extremely excited by the discovery of sulphide mineralisation
along strike from Maibele North. The intersection demonstrates the great mineral potential of
the region and supports BML’s exploration strategy of securing a majority landholding over the
Limpopo Mobile Belt in Botswana.
Furthermore, the Board is highly encouraged by the continuing 100% success rate of the
SQUID EM technique in identifying sulphide mineralisation in the region. Hole MNRC001 is the
first regional test of a SQUID EM conductor with strong conductors evident at a further 6 high
priority targets on both 100% owned BML ground and JV ground with BCL remaining to be
tested. All of the high priority targets contain conductors associated with ultramafic rock types
and encouraging geochemical anomalies.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
Figure 1: Location of the PL 59/2008 drill holes at Maibele North Extension showing the
>3km long VTEM anomaly (light blue to red colours on background image) and recently
detected SQUID EM conductors (Pink Rectangles). The current holes are marked as
MNRC001, 002, 003. Background = regional VTEM image.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
Figure 2: Cross section through MNRC001 showing the down-hole location of the
disseminated sulphide intersection in relation to the modelled SQUID EM conductor.
This is the first hole into the very strong, 500m long E4 conductor.
It is common within the Maibele North orebody for thick disseminated sulphide intersections to
coalesce into narrower massive and/or semi-massive zones within a very short distance. The
presence of sulphides at Maibele North Extension provides proof of the geological model and
targeting strategy employed by BML and provides great encouragement for the future
discovery of potential massive sulphide accumulations at the prospect.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
Drill Program Details
An initial program of 3 drill holes for 775 metres of RC drilling was proposed to test the
conductors at Maibele North Extension. These conductors rank as the highest priority targets
due to:
Close proximity along strike to Maibele North.
Multiple conductors of increasing conductivity (to over 1500s).
Shallow depth (~165m).
Multiple targets of a cumulative strike to 900m – possibly indicates a large system with
potential for numerous orebodies.
The program commenced early in October 2015.
Target
X
Y
ELEV INCLINATION AZI DEPTH
(UTM36) (UTM36)
(m)
(m)
MNRC003 636747
7597588
865
60
330
275
MNRC002 637432
7597918
865
60
330
250
MNRC001 638766
7598208
865
60
335
250
Table 1: Details of the proposed holes for Maibele North Extension.
Progress
To Be Drilled
Underway
Complete
MNRC00
1
MNRC002
MNRC003
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
Figure 3: Location of the PL 59/2008 proposed drill holes at Maibele North Extension and
the prospects spatial relationship to the Maibele North orebody. Background = regional
VTEM image.
Figure 4: Location of the PL 59/2008 prospects in relation to Maibele North and the
interpreted Maibele North mineralised trend. Background is the regional VTEM image.
Figure 5: Shows the potential strike length and its direction through BMLs 100% owned
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
PL 59/2008. The three VTEM anomalies show up in red at Maibele North Extension and
Mashambe.
The market will be kept informed as further drilling results become available.
Patrick Volpe
Chairman
Tel: +61 3 9855 1885
Fax: +61 3 9855 2885
Email: patv@botswanametals.com.au
Web: www.botswanametals.com.au
The information in this report that relates to Exploration Results is based on, and fairly represents, information and
supporting documentation compiled by BML staff on site and provided to Mr Steve Groves who is a Member of
The Australasian Institute of Mining and Metallurgy. Mr Groves is a consulting geologist to BML and has
previously been employed as the Exploration Manager at BML. Mr Groves has sufficient experience which is
relevant to the style of mineralisation and type of deposit under consideration and to the activity which he is
undertaking to qualify as a Competent Person as defined in the 2012 Edition of the ‘Australasian Code for
Reporting of Exploration Results, Mineral Resources and Ore Reserves’. Mr Groves consents to the inclusion in
this report of the matters based on his information in the form and context in which it appears.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
APPENDIX 1 – JORC Code, 2012 Edition – Table 1
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections)
CRITERIA JORC Code Explanation
Sampling
techniques
Nature and quality of sampling (eg cut
channels, random chips, or specific
specialised industry standard measurement
tools appropriate to the minerals under
investigation, such as down hole gamma
sondes, or handheld XRF instruments, etc).
These examples should not be taken as
limiting the broad meaning of sampling.
Include reference to measures taken to
ensure sample representivity and the
appropriate calibration of any measurement
tools or systems used.
Aspects of the determination of mineralisation
that are Material to the Public Report.
In cases where ‘industry standard’ work has
been done this would be relatively simple (eg
‘reverse circulation drilling was used to obtain
1 m samples from which 3 kg was pulverised
to produce a 30 g charge for fire assay’). In
other cases more explanation may be
required, such as where there is coarse gold
that has inherent sampling problems. Unusual
commodities or mineralisation types (eg
submarine nodules) may warrant disclosure of
detailed information.
Drilling
techniques
Drill sample
recovery
Commentary
The holes in discussed in this release
are Reverse Circulation. Samples are
taken at 1m intervals using a riffle
splitter attached to the cyclone on the
drill rig.
Drill type (eg core, reverse circulation ,openhole hammer, rotary air blast, auger, Bangka,
sonic, etc) and details (eg core diameter, triple
or standard tube, depth of diamond tails, face
sampling bit or other type, whether core is
oriented and if so, by what method, etc).
All holes in this release are Reverse
Circulation with a face-sampling
hammer bit.
Drillholes are mostly orientated
between 320° and 350°, inclined
between 50° and 65°.
Method of recording and assessing core
and chip sample recoveries and results
assessed.
Measures taken to maximise sample
recovery and ensure representative nature
of the samples.
Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gain of fine/coarse
material.
Botswana Metals Limited
Sample recovery was observed to be
adequate for the drill hole reported on.
Where issues were encountered with
sample recovery, it was due to holes
in the inner tubes of the drill rods and
rectified immediately. No sample
recovery issues were observed in the
sulphide zone.
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
CRITERIA JORC Code Explanation
Logging
Sub-sampling
techniques
and sample
preparation
Whether core and chip samples have been
geologically and geotechnically logged to a
level of detail to support appropriate Mineral
Resource estimation, mining studies and
metallurgical studies.
Whether logging is qualitative or
quantitative in nature. Core (or costean,
channel, etc) photography.
The total length and percentage of the
relevant intersections logged.
If core, whether cut or sawn and whether
quarter, half or all core taken.
If non-core, whether riffled, tube sampled,
rotary split, etc and whether sampled wet or
dry.
For all sample types, the nature, quality and
appropriateness of the sample preparation
technique.
Quality control procedures adopted for all
sub-sampling stages to maximise
representivity of samples.
Measures taken to ensure that the sampling
is representative of the in situ material
collected, including for instance results for
field duplicate/second-half sampling.
Whether sample sizes are appropriate to
the grain size of the material being
sampled.
Commentary
Botswana Metals Limited
RC chips are sieved and washed prior
to being logged. A record of each
meter is kept as washed chips in 20m
RC chip trays..
RC cuttings are logged in appropriate
detail including identification of
lithology, structure, alteration,
mineralization and other notable
characteristics. All RC cuttings will be
photographed with beginning, ending
and intermediate intervals clearly
marked on each box.
Samples for assay shall be collected on
a 1 sample per metre basis.
The weight of sample will depend on
the element or mineral and will be
defined by the BCL team.
A clean, dry splitter free of rust and
damage should be used.
Care should be taken to ensure the
sample is not spilt or slopped when
transferred to the splitter, and is evenly
spread across the riffles.
The best way achieve this is to roll up
the bulk bag top, carefully lay the bag
upside down on the riffle, and then pull
the bag up. This should allow the
sample to spread equally over the riffle
bed.
The sample should be assisted through
the splitter by tapping the sides with a
rubber mallet if necessary.
Similarly, clods of sample should not be
forced through the splitter, but
apportioned
manually
in
a
representative manner.
Excessively damp or wet samples
should not be put through the splitter.
These should be sampled by tube or
grab sampling (the later only were
nothing else is possible).
Damp and wet samples should not be
put through the splitter. These should,
where possible, be allowed to dry
naturally before being weighed and
then put through the rifle splitter. Where
this is not practical, e.g. during the rainy
season a strategy should be formulated
to deal with these samples.
The splitter should be thoroughly
cleaned
between
each
sample,
preferably with an air gun attached to
the drill rig compressor. Material
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
CRITERIA JORC Code Explanation
Commentary
Quality of
assay data
and
laboratory
tests
Verification
of sampling
and
assaying
Location
of data
points
adhering to the splitter is also a source
of potential contamination which is
avoided by ensuring the splitter is not
corroded or bent, kept dry and cleaned
out between each sample, preferably
using a high pressure air hose attached
to the rig compressor.
Where a high pressure air hose
attached to the rig compressor is not
available a medium strength bristle
paint brush may be used.
.
The nature, quality and appropriateness of
the assaying and laboratory procedures
used and whether the technique is
considered partial or total.
For geophysical tools, spectrometers,
handheld XRF instruments, etc, the
parameters used in determining the
analysis including instrument make and
model, reading times, calibrations factors
applied and their derivation, etc.
Nature of quality control procedures
adopted (eg standards, blanks, duplicates,
external laboratory checks) and whether
acceptable levels of accuracy (ie lack of
bias) and precision have been established.
The verification of significant intersections
by either independent or alternative
company personnel.
The use of twinned holes.
Documentation of primary data, data entry
procedures, data verification, data storage
(physical and electronic) protocols.
Discuss any adjustment to assay data.
Blanks, duplicates and standards are
inserted at a rate of approximately
13%, although the blank material is
appears to have elevated values of Ni
and Cu. The duplicates are prepared
and inserted by the laboratory and are
not inserted blindly by the onsite
geologist. The performance of the
CRM analyses is acceptable.
No verification work of significant
intersections has been completed
The Competent Person confirmed the
collar positions and sampling intervals
onsite.
No twin holes have been drilled
No statistical adjustments to data
have been applied
Accuracy and quality of surveys used to
locate drill holes (collar and down-hole
surveys), trenches, mine workings and
other locations used in Mineral Resource
estimation.
Specification of the grid system used.
Quality and adequacy of topographic
control.
Botswana Metals Limited
All of the drillhole collars have been
surveyed using a DGPS.
Down-the-hole surveys were
conducted for all holes.
The grid system for the project is UTM
WGS84.
The topography model was derived
from the drillhole collar elevations and
modelled in Leapfrog.
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
Section 2 Reporting of Exploration Results
(Criteria in this section apply to all succeeding sections)
CRITERIA
Mineral tenement
and land tenure
status
JORC Code Explanation
Type, reference name/number, location
and ownership including agreements or
material issues with third parties such as
joint ventures, partnerships, overriding
royalties, native title interests, historical
sites, wilderness or national park and
environmental settings.
The security of the tenure held at the
time of reporting along with any known
impediments to obtaining a licence to
operate in the area.
Acknowledgment and appraisal of
exploration by other parties.
Commentary
The results reported in this
announcement are located in PL 59/2008
which is a granted Exploration Licence
held by African Metals Limited, a 100%
owned subsidiary of Botswana Metals
Limited.
PL 59/2008 is 100% owned by BML
PL 59/2008 was recently extended for a
further two years and is in good standing.
Geology
Deposit type, geological setting and
style of mineralisation.
PL 59/2008 contains prospects hosted
within the Magogaphate Shear Zone - a
major geological structural feature,
generally considered to mark the
boundary between the Archaean aged
(>2.5 billion year old) Zimbabwean
Craton and the Limpopo Belt or
Limpopo Mobile Zone (LMZ). . The
nickel-copper deposits of Selebi Phikwe
lie within the northern part of the Central
Zone of the Limpopo Mobile Belt, whilst
the nickel copper deposits of Phoenix,
Selkirk and Tekwane lie in the
Zimbabwean Craton. The Central Zone
of the LMZ comprises variably deformed
banded gneisses and granitic gneisses,
infolded amphibolites and ultramafic
intrusions that that have the potential to
host Ni-Cu sulphide mineralization. NiCu-PGE mineralization at Maibele North
and Airstrip copper is spatially
associated with an ultramafic intrusion.
Drill hole
Information
A summary of all information material to
the understanding of the exploration
results including a tabulation of the
following information for all material drill
holes:
o easting and northing of the drill
hole collar
Exploration
done by other
parties
Interpretations and conclusions in this
announcement refer in part to results
generated by historic exploration work
conducted by Roan Selection Trust,
Falconbridge, Cardia Mining and
Botswana Metals.
Botswana Metals considers all previous
exploration work to have been
undertaken to an appropriate professional
standard.
Botswana Metals Limited
Refer to Appendix 2.
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
CRITERIA
Data
aggregation
methods
JORC Code Explanation
o elevation or RL (Reduced Level –
elevation above sea level in
metres) of the drill hole collar
o dip and azimuth of the hole
o down hole length and interception
depth
o hole length.
If the exclusion of this information is
justified on the basis that the information
is not Material and this exclusion does
not detract from the understanding of the
report, the Competent Person should
clearly explain why this is the case.
In reporting Exploration Results,
weighting averaging techniques,
maximum and/or minimum grade
truncations (eg cutting of high grades)
and cut-off grades are usually Material
and should be stated.
Where aggregate intercepts
incorporate short lengths of high
grade results and longer lengths of
low grade results, the procedure used
for such aggregation should be stated
and some typical examples of such
aggregations should be shown in
detail.
The assumptions used for any
reporting of metal equivalent values
should be clearly stated.
Commentary
With regards to the Maibele North MRE:
Mineralised intersections are
composited to 2 m lengths per Zone.
No discernible relationship exists
regarding sample length and grade.
With regards to reported drill intersections
Where uneven sampling intervals have
contributed to an averaged result, the
result has been calculated by a
weighted average technique that
incorporates the interval width of each
contributing sample.
A grade cut off of 0.3% and internal
dilution of <2m has been used in the
calculation of significant intercepts.
No grade truncations have been applied
to the data.
The Maibele North ore is interpreted to be
genetically and mineralogically similar to
the ore treated at the nearby Selebi
Phikwe smelter where current recovery
grades in the flotation plant average 84%
for Ni and 95% for Cu. Where Ni Eqv
calculations have been undertaken on
historic assay results it has been
assumed that similar high recoveries will
be achievable. The current drill program
has been designed to assess the
metallurgical properties of the Maibele
North mineralisation and the indicative
recoveries will be published in due
course.
Given that that the Maibele North project
is currently the subject of a Joint Venture
with the nearby Mine and Smelter
operator, BCL, BML assumes that no
impediments in recovering and selling the
metals contained in the deposit would
exist provided an viable economic
resource can be defined.
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
CRITERIA
Relationship
between
mineralisation
widths and
intercept lengths
JORC Code Explanation
These relationships are particularly
important in the reporting of
Exploration Results.
If the geometry of the mineralisation
with respect to the drill hole angle is
known, its nature should be reported.
If it is not known and only the down hole
lengths are reported, there should be a
clear statement to this effect (eg ‘down
hole length, true width not known’).
Diagrams
Appropriate maps and sections (with
scales) and tabulations of intercepts
should be included for any significant
discovery being reported These should
include, but not be limited to a plan view
of drill hole collar locations and
appropriate sectional views.
Plan view and/or cross section maps of
the reported drill holes are included in this
announcement.
Where comprehensive reporting of all
Exploration Results is not practicable,
representative reporting of both low and
high grades and/or widths should be
practiced to avoid misleading reporting of
Exploration Results.
The results in this announcement are
interpreted to lie within the plane of a
mineralized trend that is coincident with
an ultramafic intrusion and encompasses
the Maibele North Extension Prospect,
Maibele North and Airstrip Copper
Prospects.
Other exploration data, if meaningful and
material, should be reported including (but
not limited to): geological observations;
geophysical survey results; geochemical
survey results; bulk samples – size and
method of treatment; metallurgical test
results; bulk density, groundwater,
geotechnical and rock characteristics;
potential deleterious or contaminating
substances.
The location of drill holes referred to in
this document were based on
interpretation of Airborne and ground
geophysical data by professional,
independent geophysical consultants.
VTEM and SQUID EM methods were
used and processing and interpretation
was completed by Spectral Geophysics
from Gaborone, Botswana
Balanced
reporting
Other
substantive
exploration
data
Further work
The nature and scale of planned
further work (eg tests for lateral
extensions or depth extensions or
large-scale step-out drilling).
Diagrams clearly highlighting the areas
of possible extensions, including the
main geological interpretations and
future drilling areas, provided this
information is not commercially
sensitive.
Commentary
The precise geometry of the
mineralization with respect to the
drill hole angle is not known and
thus, all drill hole results are
reported as down hole length.
The drill holes in the current program are
inclined reconnaissance holes based on
the average dip of exposed units. The
orientation of the mineralization is
unknown and true width is unknown.
Geotechnical logging is under way to
address the geometry of mineralisation.
The drilling in this release is first pass,
and if successful in discovering sulphide
mineralisation, follow up work would
include further geophysical surveys and
follow up drilling
Botswana Metals Limited
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
ABN 96 122 995 073
APPENDIX 2 – Details of hole drilled
Hole
Number
MNRC001
X
(UTM36)
638766
Y
(UTM36)
7598208
ELEV
(m)
865
INCLINATION
AZI
60
335
Botswana Metals Limited
DEPTH
(m)
250
REGISTERED OFFICE
Suite 506, Level 5, 1 Princess Street Kew Vic Australia 3101
P: +61 3 9855 1885; F: +61 3 9855 2885
Email info@botswanametals.com.au
www.botswanametals.com.au
Progress
Complete
Share your feedback
Discover